Posted on: March 22, 2020 Posted by: admin Comments: 0


ASTM C + REDLINE: STANDARD SPECIFICATION FOR CONTACT- MOLDED REINFORCED THERMOSETTING PLASTIC (RTP) LAMINATES FOR. Start. Standard ASTM standard · ASTM C latest; Reinforced Plastic Piping Systems and Chemical Equipment; Plastic Building Products (ASTM VOL ) . C – 95 – This document is not an ASTM standard and is intended only to provide the user of an.

Author: Moogujin Kesho
Country: Timor Leste
Language: English (Spanish)
Genre: Technology
Published (Last): 12 April 2012
Pages: 252
PDF File Size: 5.80 Mb
ePub File Size: 4.89 Mb
ISBN: 817-6-63708-955-1
Downloads: 21885
Price: Free* [*Free Regsitration Required]
Uploader: Kagagar

Entrapped air or bubbles described are allowed, provided the surface cannot easily be broken with a pointed object, such as a knife blade. Flexural modulus—1 psi MPa. D Foreign matter must not penetrate the surface and must not contribute to entrapped air or other defects not allowed.

Astm c – astm normas fibra de vidrio

NOTE 1—The laminates covered by this specification are manufactured during fabrication of contact-molded RTP tanks, piping, and other equipment. Tensile modulus—1 psi MPa.

They are not arbitrarily selected values. Astm a Astm a Tensile strength, ultimate—17 psi MPa.

Astm c-582

The exterior surface shall also satm fully cured. Each pass of chopped roving or ply of chopped-strand mat shall be thoroughly rolled out. Plastics and is the direct responsibility of Subcommittee D Flexural strength, ultimate—18 psi MPa. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  DVS 2207-11 PDF

C Corrosion barrier Plies 1, 2, and 3 shall gel before structural plies are added. Lapped edges of adjacent layers shall be staggered. Flexural strength, ultimate—22 psi MPa. A Maximum dimensions 2 in. The resin matrix is applied by various methods, including brush, roller, or spray gun.

Tensile strength and tangent modulus of elasticity, flexural strength, glass content, thickness, hardness, chemical resistance, and surface flame-spread classification tests shall be performed to conform to the specified requirements. When such items are required, limits for each shall be agreed upon between the fabricator and the buyer. D Test Method D Test Method D NOTE 5—Maximum flame spread designation by Test Method E 84 relates to measurement and description of the properties of materials, products, or systems in response to heat and flame under controlled laboratory conditions and should not be considered or used for the description or appraisal of the fire hazard of materials, products, or systems under actual fire conditions.

Laminate designation from Table 3 shall consist of the abbreviation RTP followed by 1 type in Roman numerals; 2 class in capital letters followed by FS if required; 3 grade consisting of five Arabic numbers to designate minimum levels of physical properties and 4 thickness designated by Arabic number in decimal inches or ALL, if properties apply to all thicknesses.

However, results of this test may be used as elements of a fire risk assessment that takes into account all the factors that are pertinent to an assessment of the fire hazard or a particular end use. Current edition approved Oct.


This specification is limited to fabrication by contact molding. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

The abbreviation for reinforced thermoset plastic is RTP.

ASTM C582 – 09(2016)

Flexural modulus— psi MPa. NOTE 6—The five Arabic grade numbers designate minimum physical property levels of a laminate obtained c58 tests of representative production process samples.

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Workmanship and Finish 9. The abbreviation for reinforced thermoset plastic is RTP. Physical and Mechanical Properties 7. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

C Corrosion v582 Plies 1, 2, and 3 shall gel before structural plies are added. Additional desirable considerations in choosing a veil for zstm speci? A superscript epsilon e indicates an editorial change since the last revision or reapproval. NOTE 9—Chemical resistance can be signi? This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version.


Leave a Comment