This post explains you about the DRBD (Distributed Replicated Block Device) to understand What is DRBD (Distributed Replicated Block. Distributed Replicated Block Device (DRBD) mirrors block devices between multiple hosts. The replication is transparent to other applications on the host. This step-by-step tutorial demonstrates how to install Distributed Replicated Block Device (DRBD) on CentOS Linux.
|Published (Last):||20 June 2009|
|PDF File Size:||14.87 Mb|
|ePub File Size:||7.83 Mb|
|Price:||Free* [*Free Regsitration Required]|
You can check the status by running. I also switched off the secondary node and put much more data on the primary one. It may be easier to install the linux-server package inside the virtual machine.
Skip dbd content Home All Posts. DrBd last modified After drbd has been setup at both the nodes and one node is made primary.
This will provide the DKMS-based kernel module and userspace tools. Now we can use yum to install drbd packages.
Detecting if MySQLdump was running. This setup is of course not suitable in production, the use of loop devices it is not recommended howti to deadlock issues.
The material in this document is available under a free license, see Legal for details. Private network between the servers 4. On both servers, setup: Below are the steps: Module drbd not found. If you are using the virtual kernel as part of a virtual machine you will need to drhd compile the drbd module. I am a Linux lover and an open-source activist. Skip to primary navigation Howo to content Skip to primary sidebar You are here: DRBD kernel module and userspace utilities 3.
To do that, we will create a respond file as below and copy over to OEL so that both servers have same configuration. To report errors in this serverguide documentation, file a bug report. Once the dependency package installation has finished on both servers, we will start to install the DRBD packages. Those systems are defined as Primary node and Secondary node can switch Primary and Secndary nodes.
HowTos/Ha-Drbd – CentOS Wiki
You can think of this loosely as network Howtoo 1. After this, we will set node1 as secondary and node2 as primary. After logical device made usable, attach the drbd0 device to sdb1 disk on both nodes. More information can be found at http: Please share it and help us grow: You must see the drbdtest.
To make the modules be loaded during each boot, systemd-modules-load service is used.
How to install and setup DRBD on CentOS
Please make sure to use identical drbd versions on all nodes. I didn’t find a proper way how nowto setup loop back files during the hwto process maybe via udev rules? You can’t mount resource in node1. Shutdown your secondary node, which in this case, is drbd Since drbd0 can only be mounted on Primary node,the contents are only accessed from primary node at a time.
Hosting provided by Metropolitan Area Network Darmstadt. Any block device hard disks, partitions, RAID devices, logical volumes, etc can be mirrored. Power back on the secondary node drbd02, and watch the system hhowto back up. Powered by Social Snap. For obvious reasons, do NOT do this on drives containing any data you need for anything! Demote the primary server to yowto secondary role:.
There is always a chance of data corruption or complete data loss due to some unforeseen situation, so make sure you have backups, and you have tested restoring from those backups! This is only possible in read only mode. From a terminal enter: This throttles the howtk bandwidth that DRBD will use to perform its tasks between the 2 nodes.
Once this is done, the disks will begin to sync up. Then boot drbd01 again and enjoy the split-brain scenario! You can check the status with: Recovering from split-brain In the event of split-brain, you may be able to correct it by performing the following, but do not do this blindly!
It is used to replicate the storage devices from one node to the other node over a network. On the drbd01or whichever host you wish to be the primary, enter the following:.
This feature is only available to subscribers. In this particular case, I used squeeze-stable on the target and squeeze-backports on the source.