Posted on: May 27, 2020 Posted by: admin Comments: 0

HAMEG 8030 PDF

HAMEG INSTRUMENTS HM | Module: function generator; 7-Segment,5- digit LED; Band: ≤10MHz – This product is available in Transfer Multisort. F requency Range 50 mHz 10 MHz,. Output Voltage up to 10 Vpp (into 50 Ω). ☑ Waveforms: Sine Wave, Triangle, Square Wave, Pulse, DC. ☑ D istortion Factor. Funktionsgenerator HM Equipment HAMEG GmbH, Frankfurt, build ?, 4 pictures, 4 schematics, Germany, tubes, semiconductors, Service- or Lab.

Author: Kashakar Gojinn
Country: Germany
Language: English (Spanish)
Genre: Sex
Published (Last): 3 August 2011
Pages: 327
PDF File Size: 18.53 Mb
ePub File Size: 15.75 Mb
ISBN: 229-4-83737-418-2
Downloads: 65393
Price: Free* [*Free Regsitration Required]
Uploader: Fet

Thank You for Choosing Test Equipment Depot – Hameg No Longer Available.

This check should also be carried out for the other signal waveforms. Including the amplitude control the max. If the output of the HM unit comes into contact with components of the circuit under test, which are carrying DC voltage i. The Manufacturers and RS disclaim all warranties including implied warranties of merchantability or fitness for a particular purpose and are not liable for any damages arising from your use of or your inability to use the Information downloaded from this website.

A small circle o is now revealed on the red power button in the front centre of the mainframe. Before opening the set, you should carefully read the Safety and Warranty information on page M2 of these operating instructions. When reclosing the module, care should be taken that hzmeg guides engage correctly with the front hakeg. B – Triangle amplitude at 1 kHz Setting: Setting range from x0. The signal height should not vary by more than 0. Hxmeg permits the user to change the sweep width.

  EVERMOTION ARCHMODELS VOL 108 PDF

The instrument should be returned in its original packaging for maximum protection. Haneg var- iable frequency control with a gear ratio of 4. Output amplitude and signal connection Adaptation in decade steps to the desired amplitude range is performed by the use of two attenuators with – 20dB each, which are activated by pushbuttons. Output attenuator function Setting: Adjust 0 until the connected frequency counter indicates the value of the selected range 1 830, 10 kHz etc.

The product detailed below complies with the specifications published by RS Components. These val- ues are obtained when the generator output is terminated with 50 ohms. With the maximum amplitude of Safety Every module is manufactured and tested for use only with the mainframe HM hameh to lEC Part 1 and la Safety requirements for electronic test and measurement equipment.

Any zeroes preceding the decimal point are dropped. The selected frequency appears on the 4-digit display 0. In addition, some files are archived, so you need WinZip or WinRar to open that files. The frequency increases by a factor of The trig- ger output is short-circuit-proof and can drive several TTL inputs. Without an isolating transformer, the instrument’s power cable must be plugged into an approved three-contact electrical outlet, which meets International Electrotechnical Commission I EC safety standards.

How- ever, even experienced operators should not neglect to carefully read the following instructions and those of the mainframe HM, to avoid any operating errors and to be fully acquainted with the module when later in use. With a 50 ohms load at the outputthe signal amplitude should still be The logical front-panel layout of the module ensures rapid familiarisation with the various functions.

  GIGASET C325 BEDIENUNGSANLEITUNG PDF

These free programs can be found on this page: Intentional interruption is prohibited. If the trigger output is loaded with 50 ohms, the value falls far below the TTL level.

Add to a parts list. You can write in English language into the forum not only in Hungarian! Also some files are djvu so you need djvu viewer to open them.

Connect the distortion meter to TP1. General Information Operating condKions: This voltage is also available in DC mode. In the open-circuit condition, the available signal amplitude is about twice as high.

Funktionsgenerator HM-8030-4

Save to an existing parts list Save to a new parts list. The frequency change is linear as a function of the volt- age U and has the same value in all ranges. Electronic Jameg List Ref. Warranty Before being shipped, each plug-in module must pass a 10 hour quality control test.

HM8030-5 function generator module,5MHz

Select a screen height of 6 divisions. Looking for other manual? HAMEG will repair or replace products, which prove to be defective during the warranty period. The product does not contain any of the restricted substances in concentrations and applications banned by the Directive, and for components, the product is capable of being worked on at the higher temperatures required by lead—free soldering.

Alternatively adjust 0 and 0, until the minimum value is obtained. When removing or replacing the metal case, the instru- ment must be completely disconnected from the mains supply.

Categories:

Leave a Comment